Search found 120 matches

by Curiousjeff
21 May 2019, 19:20
Forum: Structured light scanning
Topic: David HP 3D scan and i420 format for 4K
Replies: 5
Views: 7464

Re: David HP 3D scan and i420 format for 4K

It's been some time. I think it did work ok in Fullhd.

This was with David 4.

I might have posted my settings (?) in the old forum.
by Curiousjeff
16 May 2019, 09:01
Forum: Structured light scanning
Topic: David HP 3D scan and i420 format for 4K
Replies: 5
Views: 7464

Re: David HP 3D scan and i420 format for 4K

I was the one who posted that. I have not been scanning anymore for sometime. I do remember that it worked in Windows 7, but not 10 at the time. Have you looked at the post in the old forum ? http://forum.david-3d.com/viewtopic.php?f=15&t=6550&p=33946&hilit=inogeni#p33946 I was using it ...
by Curiousjeff
07 Nov 2017, 06:55
Forum: Hardware/Accessoires
Topic: Advice on first camera selection
Replies: 11
Views: 14273

Re: Advice on first camera selection

I have used the Panasonic GH4 (rolling shutter and reduced resolution) with an HDMI capture device. I also have the PointGrey global shutter. I don't notice any real difference. With the PointGrey, I use the full resolution of the chip. At full resolution ( 2,048×1,536 ), I get faster scan time then...
by Curiousjeff
05 Nov 2017, 19:06
Forum: Hardware/Accessoires
Topic: Advice on first camera selection
Replies: 11
Views: 14273

Re: Advice on first camera selection

No, I have never tried Flexscan.
by Curiousjeff
05 Nov 2017, 17:02
Forum: Hardware/Accessoires
Topic: Advice on first camera selection
Replies: 11
Views: 14273

Re: Advice on first camera selection

oups, your are right, I was reading 1.18 instead of 1.8.

I guess you should be fine then.

Wait for an answer from Micr0, he has a lot experience. He has tested many lens
by Curiousjeff
05 Nov 2017, 16:48
Forum: Hardware/Accessoires
Topic: Advice on first camera selection
Replies: 11
Views: 14273

Re: Advice on first camera selection

I am not specialist, but for sure the image circle is not wide enough.

Maybe if you stop-down, it will be ok. I would go with a lens at least made for the chip or larger, but not smaller.
by Curiousjeff
05 Nov 2017, 15:57
Forum: Hardware/Accessoires
Topic: Advice on first camera selection
Replies: 11
Views: 14273

Re: Advice on first camera selection

FYI, the PointGrey /Flir driver does NOT allow the use of two cameras with David / HP 3D. I think this is also true for Basler. If you decide to go that route, you should buy an IS camera. Or you could buy a Flir, but the second one will need to be from another brand. I am not sure it is worth the t...
by Curiousjeff
23 Oct 2017, 13:08
Forum: Hardware/Accessoires
Topic: Camera/Projector Max Resolution and FPS
Replies: 3
Views: 5855

Re: Camera/Projector Max Resolution and FPS

Speed is determined by many factors. Acquisition speed in David software is determined by Advanced setting -> Structuredlight -> Acquisition -> Maxpatternholdingtime Lower value as long as scan is good. Mine is set to 140 With one camera (resolution of 2,048×1,536), the scan time is around 5 seconds...
by Curiousjeff
08 Sep 2017, 19:34
Forum: Structured light scanning
Topic: Adjusrting camera aperture during scan session
Replies: 1
Views: 3456

Re: Adjusrting camera aperture during scan session

No, never.

Once calibrated, I don't touch focus, angle or f-stop.
by Curiousjeff
08 Sep 2017, 10:20
Forum: Show your latest scan
Topic: David scanned by David - work in progress
Replies: 34
Views: 36477

Re: David scanned by David - work in progress

Your bad alignment is a problem. I can't help much.

The problem is:

Camera lens
AND/OR
Projector settings
AND/OR
Projector lens
AND/OR
Precision of calibration panel
AND/OR
Angle between camera and projector if out of usual range