Some of my scans

What have you scanned recently?
martan
Posts: 38
Joined: 23 May 2018, 19:18
Location: Sweden

Re: Some of my scans

Post by martan » 04 Oct 2019, 11:48

You must start the AutoIt-script before HP3Dscan. Tried that?

User avatar
OBNRacerMan
Posts: 65
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan » 04 Oct 2019, 13:57

martan wrote:
04 Oct 2019, 11:48
You must start the AutoIt-script before HP3Dscan. Tried that?
I know it. But I was not able to get any “reaction” from Deviare at all. Therefore, I had to rewrite the script (and the motor control firmware) so that it would at least process the pressing of the "S" key.
I am not a programmer, so I can not even imagine the reasons for the inoperability.

User avatar
OBNRacerMan
Posts: 65
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan » 14 Oct 2019, 20:22

There was also another attempt to scan shiny metal (without filters yet) and without matting:
20191008181116s.jpg
Appearance of the original three-finger composition - 1 :-)
20191008181140s.jpg
Appearance of the original three-finger composition - 2 :-)
no_money_06.jpg
Combined Parts
no_money_01.jpg
Finish merge - 1
no_money_02.jpg
Finish merge - 2
no_money_03.jpg
Finish merge - 3
P.S. The inscription reads - No money!

martan
Posts: 38
Joined: 23 May 2018, 19:18
Location: Sweden

Re: Some of my scans

Post by martan » 15 Oct 2019, 10:08

Nice!

:)

mading
Posts: 111
Joined: 31 Jan 2017, 13:09

Re: Some of my scans

Post by mading » 16 Oct 2019, 19:57

Well done!

User avatar
Micr0
Posts: 364
Joined: 15 Nov 2016, 15:20

Re: Some of my scans

Post by Micr0 » 17 Oct 2019, 16:23

Excellent. Thanks for sharing.
µ

User avatar
OBNRacerMan
Posts: 65
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan » 04 Nov 2019, 20:22

An additional day off (we have a holiday here), did not know what to do, and decided to conduct a check of the repeatability of the "accuracy" of the scan. Namely, how much the scan made “now” coincides with the scan made “once” (of course, during this time the camera positions, calibrations, etc. have changed many times).
I took a scan made in the summer, made a new scan and combined it. When comparing, the accuracy of 0.15 mm was chosen (at 0.5 (by default) it shows almost no difference at all) - it turned out that it fits quite well :)
2019.11.04_chizh_compare.jpg
Here is such a result

User avatar
OBNRacerMan
Posts: 65
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan » 30 Nov 2019, 21:02

Waiting for the new camera ordered by me to arrive, I decided to scan something else. This time the choice fell on my old mounting pliers:
wire cutters_01.jpg
My old wire cutters
wire cutters_02.jpg
Due to the different brightness of the handles and metal scans made a lot
wire cutters_03.jpg
Result (serifs on the handles are traces of their difficult lives)

User avatar
OBNRacerMan
Posts: 65
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan » 04 Dec 2019, 10:55

The first probes with my new MW-SUA630M camera.
So far, I have not been able to get the quality of detail like on old cameras: |
For comparison, I downloaded an old scan made by “a different camera in a different position”, with a different calibration - again everything was correctly combined with the new, “freshly baked” ones. But this is not easier.
Yellow is the scan from the old YW500Y3 camera, blue and purple are from the new:
10rub_YW-MW_01.jpg
It seems that everything is fine
10rub_YW-MW_02.jpg
It’s even noticeable that the new camera also captured the side ends of the coin
10rub_YW-MW_03.jpg
But as soon as we move apart, the problem of detail comes out
In general, we still need to train - there are a lot of settings, but they don’t have “intuitive understandability”.
P.S. The coin on the tests is the same.

Rashiga
Posts: 17
Joined: 13 Oct 2019, 14:45

Re: Some of my scans

Post by Rashiga » 04 Dec 2019, 11:08

Interesting both old and newer cameras have similar resolution right?

Post Reply