Some of my scans

What have you scanned recently?
User avatar
OBNRacerMan
Posts: 306
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

And another my "popular" model - scanned coin 10 rubles :D
Scanned coin 10 rubles
Scanned coin 10 rubles
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC HM1628MP10 (F2.8, 10Mp, 16mm) x2 & Azure 3518M3M (F1.8, 3Mp, 35mm).
mading
Posts: 268
Joined: 31 Jan 2017, 13:09

Re: Some of my scans

Post by mading »

Did you scanned flat on the turntable?
HP 3D scan, LG PF50, LG PF1500 David Calibration panels, Melamine panels, DIY rotary table. RangeVision DIY: 2x DahengMer630, 2X12 and 2X16 mm 5Mp ZK lenses, RV turntable
User avatar
OBNRacerMan
Posts: 306
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

mading wrote: 05 Mar 2021, 18:04 Did you scanned flat on the turntable?
Yes, the coin was lying on the turntable, each side was scanned at an angle (to capture the end surface too), after which the two groups of scans were manually aligned.

P.S. The previous scan with the "teddy bear" souvenir was assembled from three "full-turn" scans on a turntable, plus several single scans to capture hard-to-reach areas.
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC HM1628MP10 (F2.8, 10Mp, 16mm) x2 & Azure 3518M3M (F1.8, 3Mp, 35mm).
NARMELLA

Re: Some of my scans

Post by NARMELLA »

Were wonderful results !!!
User avatar
OBNRacerMan
Posts: 306
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

A couple of my last scans - a wrench
Preview picture
Preview picture
View the model in 3D


and screwdriver (this model has "flaws" due to the fact that the spindle turned a little during the scanning process)
Pic. 1
Pic. 1
Pic. 2
Pic. 2
View the model in 3D


To place these models on the site, the scans had to be simplified to 3% of the original number of triangles.
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC HM1628MP10 (F2.8, 10Mp, 16mm) x2 & Azure 3518M3M (F1.8, 3Mp, 35mm).
User avatar
OBNRacerMan
Posts: 306
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

I decided to make a new scan of the drill bit. Even after the usual simplification to 10% of the original number of triangles, the model remained of fairly good quality.
https://p3d.in/0qY2f
Scanned drill bit 7.0mm
Scanned drill bit 7.0mm
drill_7.0.jpg (10.83 KiB) Viewed 387 times
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC HM1628MP10 (F2.8, 10Mp, 16mm) x2 & Azure 3518M3M (F1.8, 3Mp, 35mm).
Post Reply