Some of my scans

What have you scanned recently?
User avatar
OBNRacerMan
Posts: 372
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

And another my "popular" model - scanned coin 10 rubles :D
Scanned coin 10 rubles
Scanned coin 10 rubles
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER2-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC FM12036MP5 (F2.8/5Mp/12-36mm) x2. And a handheld scanner Creality Ferret
mading
Posts: 307
Joined: 31 Jan 2017, 13:09

Re: Some of my scans

Post by mading »

Did you scanned flat on the turntable?
LG PF50, LG PF1500, RangeVision DIY: 2x DahengMer630, 2X12 and 2X16 mm 5Mp ZK lenses, RV turntable
User avatar
OBNRacerMan
Posts: 372
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

mading wrote: 05 Mar 2021, 18:04 Did you scanned flat on the turntable?
Yes, the coin was lying on the turntable, each side was scanned at an angle (to capture the end surface too), after which the two groups of scans were manually aligned.

P.S. The previous scan with the "teddy bear" souvenir was assembled from three "full-turn" scans on a turntable, plus several single scans to capture hard-to-reach areas.
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER2-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC FM12036MP5 (F2.8/5Mp/12-36mm) x2. And a handheld scanner Creality Ferret
NARMELLA

Re: Some of my scans

Post by NARMELLA »

Were wonderful results !!!
User avatar
OBNRacerMan
Posts: 372
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

A couple of my last scans - a wrench
Preview picture
Preview picture
View the model in 3D


and screwdriver (this model has "flaws" due to the fact that the spindle turned a little during the scanning process)
Pic. 1
Pic. 1
Pic. 2
Pic. 2
View the model in 3D


To place these models on the site, the scans had to be simplified to 3% of the original number of triangles.
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER2-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC FM12036MP5 (F2.8/5Mp/12-36mm) x2. And a handheld scanner Creality Ferret
User avatar
OBNRacerMan
Posts: 372
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

I decided to make a new scan of the drill bit. Even after the usual simplification to 10% of the original number of triangles, the model remained of fairly good quality.
https://p3d.in/0qY2f
Scanned drill bit 7.0mm
Scanned drill bit 7.0mm
drill_7.0.jpg (10.83 KiB) Viewed 7931 times
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER2-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC FM12036MP5 (F2.8/5Mp/12-36mm) x2. And a handheld scanner Creality Ferret
User avatar
OBNRacerMan
Posts: 372
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

Willie Lowell wrote: 16 Nov 2021, 08:51 the turntable, do you have the arduino code?
I use ScanCenter software (in the Rangevision DIY version) and a turntable, respectively, not based on Arduino (this is a custom version of the ComXim brand with a USB connection, which is produced by order of RangeVision).
P.S. At the same time, there are some options for connecting DIY tables to this software.
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER2-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC FM12036MP5 (F2.8/5Mp/12-36mm) x2. And a handheld scanner Creality Ferret
User avatar
OBNRacerMan
Posts: 372
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Some of my scans

Post by OBNRacerMan »

During the New Year holidays, I received a Revopont POP2 for a while, and decided to conduct a small comparative test with my Creality Lizard (which was half the price of POP2) and, as a kind of "starting point", a scan on my stationary SLS scanner. The plastic bust (height about 10cm) that came with POP2 was used as a test subject.

At first, I did not see any strong difference between Lizard and POP2...
2023.01.06_scan_Lz_POP2_test_01.jpg
2023.01.06_scan_Lz_POP2_test_02.jpg
2023.01.06_scan_Lz_POP2_test_03.jpg
But then it turned out that if I finalized the scan in RevoScan (and would not switch to RevoStudio later), then the quality of POP2 is noticeably higher, although there is still some "noise"
2023.01.06_scan_Lz_POP2_test_07.jpg
Also scan from RV DIY
2023.01.06_scan_Lz_POP2_test_08.jpg
2023.01.06_scan_Lz_POP2_test_09.jpg
Its surface detail, of course, cannot be compared with cheap hand-held scanners based on IR illumination.
2023.01.06_scan_Lz_POP2_test_10.jpg
P.S. A little later, in the RV DIY software, I combined a scan of myself (made with Lizard) with an existing sculpture from Revopoint :mrgreen:
2023.01.06_my_scan_01.jpg
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER2-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC FM12036MP5 (F2.8/5Mp/12-36mm) x2. And a handheld scanner Creality Ferret
mading
Posts: 307
Joined: 31 Jan 2017, 13:09

Re: Some of my scans

Post by mading »

Thanks for sharing!
LG PF50, LG PF1500, RangeVision DIY: 2x DahengMer630, 2X12 and 2X16 mm 5Mp ZK lenses, RV turntable
User avatar
Micr0
Posts: 586
Joined: 15 Nov 2016, 15:20
Location: New York City

Re: Some of my scans

Post by Micr0 »

OBNRacerMan wrote: 20 Jan 2023, 10:58 During the New Year holidays, I received a Revopont POP2 for a while, and decided to conduct a small comparative test with my Creality Lizard (which was half the price of POP2) and, as a kind of "starting point", a scan on my stationary SLS scanner. The plastic bust (height about 10cm) that came with POP2 was used as a test subject.

At first, I did not see any strong difference between Lizard and POP2...
2023.01.06_scan_Lz_POP2_test_01.jpg2023.01.06_scan_Lz_POP2_test_02.jpg2023.01.06_scan_Lz_POP2_test_03.jpg

But then it turned out that if I finalized the scan in RevoScan (and would not switch to RevoStudio later), then the quality of POP2 is noticeably higher, although there is still some "noise"
2023.01.06_scan_Lz_POP2_test_07.jpg

Also scan from RV DIY
2023.01.06_scan_Lz_POP2_test_08.jpg2023.01.06_scan_Lz_POP2_test_09.jpg
Its surface detail, of course, cannot be compared with cheap hand-held scanners based on IR illumination.
2023.01.06_scan_Lz_POP2_test_10.jpg

P.S. A little later, in the RV DIY software, I combined a scan of myself (made with Lizard) with an existing sculpture from Revopoint :mrgreen:
2023.01.06_my_scan_01.jpg
Thanks for sharing. I got a revo mini, and it's OK for some things. But I plan on refining my SL rig soon, but the mini is no replacement.
µ
Post Reply