Re: Some of my scans
Posted: 05 Mar 2021, 17:42
3D Scan Forum
the board for everyone interested in 3d scanning
https://www.3dscanforum.org/
Some of my scans
Page 13 of 15
Re: Some of my scans
Posted: 05 Mar 2021, 18:04
Did you scanned flat on the turntable?
Re: Some of my scans
Posted: 05 Mar 2021, 19:30
Yes, the coin was lying on the turntable, each side was scanned at an angle (to capture the end surface too), after which the two groups of scans were manually aligned.
P.S. The previous scan with the "teddy bear" souvenir was assembled from three "full-turn" scans on a turntable, plus several single scans to capture hard-to-reach areas.
Re: Some of my scans
Posted: 25 Mar 2021, 19:36
Were wonderful results !!!
Re: Some of my scans
Posted: 06 Aug 2021, 07:57
A couple of my last scans - a wrench
View the model in 3D
and screwdriver (this model has "flaws" due to the fact that the spindle turned a little during the scanning process)
View the model in 3D
To place these models on the site, the scans had to be simplified to 3% of the original number of triangles.
- Preview picture
and screwdriver (this model has "flaws" due to the fact that the spindle turned a little during the scanning process)
- Pic. 1
- Pic. 2
To place these models on the site, the scans had to be simplified to 3% of the original number of triangles.
Re: Some of my scans
Posted: 16 Sep 2021, 18:57
I decided to make a new scan of the drill bit. Even after the usual simplification to 10% of the original number of triangles, the model remained of fairly good quality.
https://p3d.in/0qY2f
https://p3d.in/0qY2f
- Scanned drill bit 7.0mm
- drill_7.0.jpg (10.83 KiB) Viewed 8202 times
Re: Some of my scans
Posted: 16 Nov 2021, 10:19
I use ScanCenter software (in the Rangevision DIY version) and a turntable, respectively, not based on Arduino (this is a custom version of the ComXim brand with a USB connection, which is produced by order of RangeVision).
P.S. At the same time, there are some options for connecting DIY tables to this software.
Re: Some of my scans
Posted: 20 Jan 2023, 10:58
During the New Year holidays, I received a Revopont POP2 for a while, and decided to conduct a small comparative test with my Creality Lizard (which was half the price of POP2) and, as a kind of "starting point", a scan on my stationary SLS scanner. The plastic bust (height about 10cm) that came with POP2 was used as a test subject.
At first, I did not see any strong difference between Lizard and POP2...
But then it turned out that if I finalized the scan in RevoScan (and would not switch to RevoStudio later), then the quality of POP2 is noticeably higher, although there is still some "noise"
Also scan from RV DIY
Its surface detail, of course, cannot be compared with cheap hand-held scanners based on IR illumination.
P.S. A little later, in the RV DIY software, I combined a scan of myself (made with Lizard) with an existing sculpture from Revopoint 
At first, I did not see any strong difference between Lizard and POP2...
Re: Some of my scans
Posted: 20 Jan 2023, 14:53
Thanks for sharing!
Re: Some of my scans
Posted: 20 Jan 2023, 16:14
Thanks for sharing. I got a revo mini, and it's OK for some things. But I plan on refining my SL rig soon, but the mini is no replacement.OBNRacerMan wrote: ↑20 Jan 2023, 10:58 During the New Year holidays, I received a Revopont POP2 for a while, and decided to conduct a small comparative test with my Creality Lizard (which was half the price of POP2) and, as a kind of "starting point", a scan on my stationary SLS scanner. The plastic bust (height about 10cm) that came with POP2 was used as a test subject.
At first, I did not see any strong difference between Lizard and POP2...
2023.01.06_scan_Lz_POP2_test_01.jpg2023.01.06_scan_Lz_POP2_test_02.jpg2023.01.06_scan_Lz_POP2_test_03.jpg
But then it turned out that if I finalized the scan in RevoScan (and would not switch to RevoStudio later), then the quality of POP2 is noticeably higher, although there is still some "noise"
2023.01.06_scan_Lz_POP2_test_07.jpg
Also scan from RV DIY
2023.01.06_scan_Lz_POP2_test_08.jpg2023.01.06_scan_Lz_POP2_test_09.jpg
Its surface detail, of course, cannot be compared with cheap hand-held scanners based on IR illumination.
2023.01.06_scan_Lz_POP2_test_10.jpg
P.S. A little later, in the RV DIY software, I combined a scan of myself (made with Lizard) with an existing sculpture from Revopoint
2023.01.06_my_scan_01.jpg