Page 1 of 1
Macro scanning in Modified version of FlexScan3D (Needle)
Posted: 11 Dec 2022, 18:45
by greenskynet
Hi everyone
This is a simple scan of a small needle. I've scanned it with
green light feature. It obviously enhances capturing quality. (
green light and also
blue light scanning is a nice feature available in
modified version of FlexScan3D viewtopic.php?p=5189#p5189)
The diameter of the needle is about 0.67mm and the width of the hole is about
0.3mm.
I should mention than my equipment is not perfect for macro scanning, but you can see that the result is promising
Please visit my Telegram group to see more scan results: https://t.me/DIY_3D_Scanner
Re: Macro scanning in Modified version of FlexScan3D (Needle)
Posted: 20 Jan 2023, 16:11
by Micr0
greenskynet wrote: ↑11 Dec 2022, 18:45
Hi everyone
This is a simple scan of a small needle. I've scanned it with
green light feature. It obviously enhances capturing quality. (
green light and also
blue light scanning is a nice feature available in
modified version of FlexScan3D viewtopic.php?p=5189#p5189)
The diameter of the needle is about 0.67mm and the width of the hole is about
0.3mm.
I should mention than my equipment is not perfect for macro scanning, but you can see that the result is promising
Please visit my Telegram group to see more scan results: https://t.me/DIY_3D_Scanner
D1.jpg
D2.jpg
D3.jpg
Very cool. can you post a picture set up for scanning that?
Re: Macro scanning in Modified version of FlexScan3D (Needle)
Posted: 20 Jan 2023, 19:43
by greenskynet
Micr0 wrote: ↑20 Jan 2023, 16:11
greenskynet wrote: ↑11 Dec 2022, 18:45
Hi everyone
This is a simple scan of a small needle. I've scanned it with
green light feature. It obviously enhances capturing quality. (
green light and also
blue light scanning is a nice feature available in
modified version of FlexScan3D viewtopic.php?p=5189#p5189)
The diameter of the needle is about 0.67mm and the width of the hole is about
0.3mm.
I should mention than my equipment is not perfect for macro scanning, but you can see that the result is promising
Please visit my Telegram group to see more scan results: https://t.me/DIY_3D_Scanner
D1.jpg
D2.jpg
D3.jpg
Very cool. can you post a picture set up for scanning that?
Hi Micr0
I used Daheng MER2-630-60U3M cameras (6.3MP)
20mm lenses
and a Acer K137 projector
Re: Macro scanning in Modified version of FlexScan3D (Needle)
Posted: 23 Jan 2023, 14:52
by Micr0
greenskynet wrote: ↑20 Jan 2023, 19:43
Micr0 wrote: ↑20 Jan 2023, 16:11
greenskynet wrote: ↑11 Dec 2022, 18:45
Hi everyone
This is a simple scan of a small needle. I've scanned it with
green light feature. It obviously enhances capturing quality. (
green light and also
blue light scanning is a nice feature available in
modified version of FlexScan3D viewtopic.php?p=5189#p5189)
The diameter of the needle is about 0.67mm and the width of the hole is about
0.3mm.
I should mention than my equipment is not perfect for macro scanning, but you can see that the result is promising
Please visit my Telegram group to see more scan results: https://t.me/DIY_3D_Scanner
D1.jpg
D2.jpg
D3.jpg
Very cool. can you post a picture set up for scanning that?
Hi Micr0
I used Daheng MER2-630-60U3M cameras (6.3MP)
20mm lenses
and a Acer K137 projector
Yes. I was hoping to see how you arrange your cameras and Projectors to be able to focus and scan something so small. I've always had a problem getting my cameras close enough to my projector and subject to be able to scan things smaller than 100mm.
