Helmet

What have you scanned recently?
Post Reply
martan
Posts: 96
Joined: 23 May 2018, 19:18
Location: Sweden

Helmet

Post by martan »

I friend wanted a scaled down version of a flying helmet.

Scanned in one piece so obvioulsly not perfect. Printed ok.
Attachments
Printed
Printed
Front
Front
Rear
Rear
HP 3D Scan, Optoma ML750, 2x IS DMK 23UX236 with Computar 12mm, HP calibration panel, DIY Rotary tables.
User avatar
Micr0
Posts: 586
Joined: 15 Nov 2016, 15:20
Location: New York City

Re: Helmet

Post by Micr0 »

NIce. Thanks for sharing. Did you coat the visor?
µ
martan
Posts: 96
Joined: 23 May 2018, 19:18
Location: Sweden

Re: Helmet

Post by martan »

I sprayed it with AESUB blue. Not the perfect spray - i smells and it actually leaves
a bit of traces after "vanishing".

I will continue to use it, but maybe not to everything :-)
HP 3D Scan, Optoma ML750, 2x IS DMK 23UX236 with Computar 12mm, HP calibration panel, DIY Rotary tables.
User avatar
OBNRacerMan
Posts: 372
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Helmet

Post by OBNRacerMan »

Great scan. What calibration chart was used (as I understand it, this is a real, full-sized helmet scanned)?
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER2-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC FM12036MP5 (F2.8/5Mp/12-36mm) x2. And a handheld scanner Creality Ferret
martan
Posts: 96
Joined: 23 May 2018, 19:18
Location: Sweden

Re: Helmet

Post by martan »

Yes, real helmet. I used the 240mm calibration panel for the first time. RMS numbers below 0,1 (!)

2x IS-cameras with computar 12mm, Optoma ML750, and "IKEA manual turnatable". As usual :-)
HP 3D Scan, Optoma ML750, 2x IS DMK 23UX236 with Computar 12mm, HP calibration panel, DIY Rotary tables.
User avatar
OBNRacerMan
Posts: 372
Joined: 12 Aug 2019, 09:46
Location: Obninsk, Russia

Re: Helmet

Post by OBNRacerMan »

martan wrote: 21 Jan 2020, 07:41 RMS numbers below 0,1 (!)
Great! I usually have RMS in the range 0.5 - 1.3 on tables from 30mm to 80mm :D
Soft: RangeVision DIY, Calibration panel/Rotary tables - RangeVision, Prj: LG PF1500G, Cam: Daheng Mercury MER2-630-60U3M-L (USB3.0, monochrome) x2, Obj: ZLKC FM12036MP5 (F2.8/5Mp/12-36mm) x2. And a handheld scanner Creality Ferret
erapip
Posts: 56
Joined: 16 Dec 2016, 07:16

Re: Helmet

Post by erapip »

martan wrote: 21 Jan 2020, 07:41 Yes, real helmet. I used the 240mm calibration panel for the first time. RMS numbers below 0,1 (!)

2x IS-cameras with computar 12mm, Optoma ML750, and "IKEA manual turnatable". As usual :-)
How did you manage to use 2xIS camera? When i try to connect one always freezes. What model do you use?
Thanks in advance!
martan
Posts: 96
Joined: 23 May 2018, 19:18
Location: Sweden

Re: Helmet

Post by martan »

I use this one:
https://www.theimagingsource.com/produc ... mk23ux236/

I would say that you have a USB-problem. I struggled a lot with this (actually with the Oculus Rift VR-goggles).

I use USB card Inateck PCI-e to USB 3.0 (4 Ports)
The big thing for me was to set the correct PCIe-generation manually in BIOS. I have Gen3 on my Motherboard and the card is a Gen 2 (?).
This gives me steady 54fps on both cameras.

My Asus laptop works almost as good out of the box but i keep proj/camera cables apart as much as possible.
HP 3D Scan, Optoma ML750, 2x IS DMK 23UX236 with Computar 12mm, HP calibration panel, DIY Rotary tables.
Post Reply